Hi David

It appears that you have been looking for existing models, however, most existing models are trained on either COCO or some other very generic dataset. So, if you want to identify just animals, you may be better off training your own model. It seems no one in this thread mentioned yet that it is possible to do transfer learning on existing models, which keeps most of the "visual part" of the model as is, but just changes the classification part so it can identify other things. This way you can take an existing model trained on COCO and in a fraction of the time it takes to train a full model, just retrain that for your animals.

Also have a look at your requirements for the inferencing stage. Some models take long in training but are superfast in inference and others are slow in both cases but very accurate, etc. If you want semi-realtime inferencing, you are probably looking at single shot detectors (SSD), and not RCNNs.

Have you considered Arduinos?

Look into evorta.  

It is an Australian company that is doing exactly this.  

You can.

• Have an offline camera that can be trained to ID specific species, 
• send you just the photos of those species via satellite 
• Or if you can get 4g send you all the photos to their online database. 
• They also have an online database that allows you to analyse the data in real time. 
• They can also hack normal camera traps so they can send photos back to the main unit to process and send valid photos.  That way you only need one ‘smart’ camera.  All the rest can be your exsisting cameras. You just need to use your sd card slot.  

Here is an article here  

 Best to contact him through email.  

I’ll send it to you privately 

Hi Chris, we looked into solar powered battery systems for Reconyx because we had a customer want to use them along side our Solar BAR bioacoustic recorder. We made a power out port and custom cable to run his camera traps and also so someone else in France could use them with another company's bat detector. Typically they had a 10W solar panel, 8Ah lead acid battery and a charge controller built into a sealed box stuck to the back of the solar panel. You could save some weight by choosing a LiFePo4 battery instead like this but you can only use them when you know you will charge them when the temperature is over 0 degrees C or you will damage them. Use lead acid if you're not sure they will always be charged over 0 degrees C.

You can find MPPT solar charge modules on Aliexpress and Ebay. I used the search term "mppt solar charge module". LiFePo4 can be charged at the same voltage as lead acid and most lead acid chargers do constant current charging anyway becuse you can use it with lithium batteries then as well. It's better to get a LiFePo4 charger if you can get it to make sure it's constant current then constant voltage but they're pretty tough unless you charge them under 0 degrees.

A typical 10W 12v solar panel will have it's Maximum Power Point at 18v so your charge controller must be set to 18v as it's input voltage. The panel will make a maximum of 20v when it's not plugged into anything. A 10W panel will make about 0.5A so if you pick a 3A charger it'll get limited to 0.5A because of the panel.

A module like this where the parameters are adjustable might be good.

On the other hand if you want something that can't be fiddled with after you made it get one with 18v MPPT voltage and set to charge a lead acid or whatever battery chemistry that you're using. Often using terms like lead acid when you search will help narrow it down. If you're going to use a 12v LiFePo4 note that's is a 3S 3.7v pack. That is 3 x 3.7v makes 11.1v (which they call a 12v pack).

If you're unsure feel free to email me at [email protected] to check what you're planning to buy.

If you're gluing a box with the charge controller onto the back of a solar panel use neutral cure silicone or check with the supplier about what glue you can use if you need something stronger than that.

If there is sufficient demand for these sorts of accessories please let me know and we can consider it as a product. 

Mark

Hey there! Not sure what your funding constraints are but I have been using Reolink Go PT, which is solar powered. This model has been discontinued. However they have an upgraded version. Adding link here. 



I have used this in the field in the swaps of Florida, exposed to heat, humidity and moisture. It has held up really well. Great sensors that can even be adjusted for sensitivity.

Not sure if audio data would be of any use to you, but if so FishSounds has some - I just tried their search function and there is a location tag for 'Mediterranean & Black Sea'. 

You might try reaching out to the folks at Name that Fish, Innovasea, or perhaps an entity on the Fisheries Tech list would have Mediterranean stuff? 

Hi,

If this is still relevant, you can try reaching out to the Belmaker lab, they do BRUV surveys in the eastern Mediterranean and have hours of video, some of it I believe is annotated. Particularly, Shahar might be helpful, he's the PhD student running point on the project.

We have made available our underwater videos on YouTube as a playlist https://www.youtube.com/playlist?list=PLnhVZKKy8WkZKriCIV6r7upWhHNVrU_7L 

It's about 1.113 short video clips with annotation and each is linked to the corresponding www.iNaturalist.org observations. The iNaturalist.org observations are research quality and have been uploaded to GBIF.org. The observations have been made between 2014 and 2022 around the Ionian Islands (Greece).

If you would need the original videos please contact me.